A subcutaneous injection (abbreviated as SC, SQ, sub-cu, sub-Q or subcut) is administered as a bolus into the subcutis, the layer of skin directly below the dermis and epidermis, collectively referred to as the cutis. A person with Type I diabetes mellitus typically injects insulin subcutaneously. High Quality Content by WIKIPEDIA articles! Places on the body where people can inject insulin most easily are: * The outer area of the upper arm. * Just above and below the waist, except the area right around the navel (a 2-inch circle). * The upper area of the buttock, just behind the hip bone. * The front of the thigh, midway to the outer side, 4 inches below the top of the thigh to 4 inches above the knee. Subcutaneous injections are highly effective in administering vaccines and such medications as insulin, morphine, diacetylmorphine or goserelin.
|Формат:|| Страниц 124|
Lambert M. S.
Книга по Требованию
|Spin Injection in Quantum Well Spin-Light Emitting Diodes. Studies of Spin-Polarized Electrons in GaAs-Based Quantum Well Light Emitting Diodes Книга по Требованию Grigorios I. |
The discussion also contains an introduction on the physics of spin orientation in semiconductors along with a review of optical and magneto-optical techniques used for the investigation of spin-LEDs.
|OPTO-INJECTION INTO SINGLE LIVING CELLS BY FEMTOSECOND NIR LASER. A NOVEL TECHNIQUE OF DELIVERING MATERIALS INTO LIVEING CELLS Книга по Требованию Cheng P. |
Pore size was found dependent on incident laser intensity.
|High-Speed Modulation of Semiconductor Lasers by Optical Injection Locking. From Basics to Modern Advances Книга по Требованию |
The injection locking technique allows the lasers to exceed their fundamental modulation speed limit, allowing for greater communication speeds.
|Indirect injection Книга по Требованию Frederic P. M. |
In an internal combustion engine, the term indirect injection refers to a fuel injection where fuel is not directly injected into the combustion chamber.
|Injection Molding Книга по Требованию Frederic P. M. |
After a product is designed, usually by an industrial designer or an engineer, molds are made by a moldmaker (or toolmaker) from metal, usually either steel or aluminium, and precision-machined to form the features of the desired part.
|Rheumatism, Rheumatoid Arthritis and Subcutaneous Nodules Книга по Требованию Hawthorne C.O. |
|Subcutaneous Hydrocarbon Protheses Книга по Требованию Kolle F.S. |
|VCO Gain and Injection-Locking to Measure Inductor Coupling on ICs. Using Oscillator Gain and Injection-Locking to Measure On-Chip Inductor Coupling Книга по Требованию Peter P. |
The demonstrated oscillator gain shows how oscillators can be used in non-traditional roles such as active filters or amplifiers.
|Asphalt Injection (PS Vita) |
В автопарке представлены 52 лицензированные машины всемирно известных марок, в числе которых Ferrari, Lamborghini, Aston Martin и Mercedes.
|Relatively Max, Injective and Extending (CS) modules Themes in Torsion Theory. Книга по Требованию Stelios C. |
The purpose of this book is to generalize to the torsion-theoretic setting various concepts and results from the theory of rings and modules.
|Costs of injecting drug use. Benefits of treatment Книга по Требованию Ian S. |
This study finds that it is cost-effective to provide anti-viral therapy to drug users.
|The New Treatment Of Snake-bite, With Plain Directions For Injecting Книга по Требованию Britton H.G. |
|Injective hull Книга по Требованию Frederic P. M. |
In mathematics, especially in the area of abstract algebra known as module theory, the injective hull (or injective envelope) of a module is both the smallest injective module containing it and the largest essential extension of it. Injective hulls were first described in (Eckmann Please note that the content of this book primarily consists of articles available from Wikipedia or other free sources online.